Tools

  • B0506 Mugen Seiki Snap Ring pliers

    Mugen Seiki

    B0506 Mugen Seiki Snap Ring pliers

    These snap ring plies work great for all different sizes of “C” clips. The harden tips and a small angle to grab the clip and hold it tight while removing it from the part. Rubber handed for good grip. The pliers do have a coat of oil on them...

    $18.49
    Out of stock
  • B0549 Turnbuckle Wrench 4mm :MTC1

    Mugen Seiki

    B0549 Turnbuckle Wrench 4mm :MTC1

    Aluminum turnbuckle and camber adjusting tool. A great tool to make easy fine tune adjustments for both front / rear camber links and steering arm tie-rods. Will fit a 4mm turnbuckle. This tool will also work for the camber and steering tie-rods for the...

    $15.99
    Add to Cart
  • FP2117 FP 17mm Magnetic Wheel Wrench

    Flash Point Racing Products

    FP2117 FP 17mm Magnetic Wheel Wrench

    This is the Flash Point R/C 17mm Magnetic Wheel Wrench.  It’s a machined light weight 17mm wheel wrench that has a built-in magnet.  One end of the wheel wrench is open and allows you to remove the set-screws that hold the pin...

    $33.99
    Add to Cart
  • B0548 Rebound Stop Gauge (Droop)

    Mugen Seiki

    B0548 Rebound Stop Gauge (Droop)

    This is Mugen rebound stop gauge. This is a must have tool to measure the droop (length) of your shocks on your Buggy and Truggy. You can check shock droop (length) from 90mm to 135mm. A simple tool that is very easy to use. Check out the video to see it...

    $24.99
    Add to Cart
  • B0547 Alum Ride Height Gauge: Buggy, Truggy, GT

    Mugen Seiki

    B0547 Alum Ride Height Gauge: Buggy, Truggy, GT

    This is the perfect ride height gauge for 1/8 nitro and electric buggy’s and truggy’s or other cars with a minimum ride height of 18mm. This ride height gauge measures the chassis ride height from 18mm – 45mm. It is constructed from...

    $69.99
    Add to Cart
  • B0545 Pinion Gear Tool for MRX6R, GT7

    Mugen Seiki

    B0545 Pinion Gear Tool for MRX6R, GT7

    A universal pinion gear tool for both 1/8 on road and GT nitro cars with 2 speed transmissions. Included is an aluminum hub to hold and lock either 1/8 on road or GT clutch bell and a 2nd tool to install and tighten up both 1st and 2nd gear pinions onto...

    $44.99
    Out of stock
  • B0542 Pinion Gear Tool: MTX6, 5

    Mugen Seiki

    B0542 Pinion Gear Tool: MTX6, 5

    A universal pinion gear tool for the MTX6R. Included is an aluminum hub to hold and lock the clutch bell and a 2nd tool to install and tighten up both 1st and 2nd gear pinions onto the clutch bell. This tool allows tightening the pinion gears without...

    $44.99
    Add to Cart
  • B0540 Height Gauge

    Mugen Seiki

    B0540 Height Gauge

    This is a high quality aluminum height gauge for both 1/8 and 1/10 nitro and electric cars. You can check the droop on both the front and rear of your car. Measurements go from -2 – 12mm. This tool needs to be used with B0529 or a set of chassis...

    $26.99
    Add to Cart